MODEL: HD-1000BE JANOME HD-1000BE Service & Parts Manual

Citation preview

JANOME HD-1000BE Service & Parts Manual

MODEL: HD-1000BE

Manualsoncd.com

CONTENTS SERVICE ACCESS (1) FACE COVER, TOP COVER....................................................... 1 SERVICE ACCESS (2) BASE, BED COVER.................................................................... 2 SERVICE ACCESS (3) BELT COVER.............................................................................. 3 MECHANICAL ADJUSTMENT ZERO POSITION OF ZIGZAG STITCH............................................................................. 4 NEEDLE SWING................................................................................................................ 5 NEEDLE DROP POSITION IN NEEDLE PLATE HOLE..................................................... 6 PRESSER BAR HEIGHT AND DIRECTION...................................................................... 7 CLEARANCE BETWEEN NEEDLE AND HOOK............................................................... 8 NEEDLE BAR HEIGHT...................................................................................................... 9 NEEDLE TIMING TO SHUTTLE...................................................................................... 10 LOWER SHAFT PLAY.......................................................................................................11 FEED LIFTING CAM POSITION...................................................................................... 12 FEED DOG HEIGHT........................................................................................................ 13 STRETCH STITCH FEED BALANCE.............................................................................. 14 BAR-TACK FEED OF BUTTONHOLE............................................................................. 15 BUTTONHOLE FEED BALANCE..................................................................................... 16 MOTOR BELT TENSION.................................................................................................. 17 PARTS LIST.............................................................................................................. 18 - 35

SERVICE ACCESS (1) FACE COVER TO REMOVE: 1. Remove the setscrew (A), and remove the face cover. TO INSTALL: 2. Follow the above procedure in reverse.

TOP COVER TO REMOVE: 1. Remove the setscrews (B), (C), and remove the top cover. TO INSTALL: 2. Follow the above procedure in reverse.

(C)

(B)

Top cover

(A)

Face cover

1 Manualsoncd.com

SERVICE ACCESS (2) BASE TO REMOVE: 1. Remove the 3 setscrews (A) and the 2 setscrews (B), and remove the base. TO INSTALL: 2. Follow the above procedure in reverse.

BED COVER TO REMOVE: 1. Remove the 2 setscrews (C), and remove the bed cover. TO INSTALL: 2. Follow the above procedure in reverse.

Base

Setscrew (A)

Bed cover

Setscrew (B)

Setscrew (C)

2

SERVICE ACCESS (3) BELT COVER TO REMOVE: 1. Remove the top cover (see page 1). 2. Remove the setscrew (A), and remove the belt cover. TO INSTALL: 3. Follow the above procedure in reverse.

Setscrew (A)

Belt cover

3 Manualsoncd.com

MECHANICAL ADJUSTMENT ZERO POSITION OF ZIGZAG STITCH To check: When the pattern selector dial is set at "

", the needle bar should not swing.

Adjustment procedure: 1. Remove the top cover (see page 1). 2. Turn the balance wheel toward you until cam follower (A) comes up to the top of convex of basic zigzag cam (B) as shown. 3. Loosen the nut with the wrench. 4. Turn the setscrew (C) clockwise slightly until the play of release cam follower (D) is eliminated. 5. Tighten the nut.

Top of convex of basic zigzag cam (B) Cam follower (A)

Zigzag width adjusting pin

Cam follower (A)

Setscrew (C)

Nut

Release cam follower (D)

4

MECHANICAL ADJUSTMENT NEEDLE SWING To check: Adjust the needle swing according to the following procedure, If the needle bar starts moving sideways while the needle is in the fabric when sewing the zigzag pattern (with maximum zigzag width). Adjustment procedure: 1. Set the pattern selector dial at maximum zigzag width, and remove the top cover (see page 4). 2. Loosen the two setscrews. 3. Adjust the needle swing by turning the handwheel, while holding the worm so as not to rotate it, until the needle swing starts at 2–3 mm above the needle plate after the needle has come out of the right side of the needle hole. 4. Tighten two setscrews. 5. Attach the top cover. NOTE: After adjusting the needle swing, check that the upper shaft worm and gear rotate smoothly without any backlash between them.

Upper shaft worm

Setscrew (2 pcs.)

2–3mm

5 Manualsoncd.com

MECHANICAL ADJUSTMENT NEEDLE DROP POSITION IN NEEDLE PLATE HOLE To check: When the pattern selector dial is set at " hand side of needle is 0.3 to 0.5 mm.

", the clearance between the edge of hole and the left

Adjustment procedure: 1. 2. 3. 4. 5. 6.

Set the pattern selector dial at " ". Change the needle to size 14. Remove the face plate (see page 1). Loosen the setscrew (A). Turn the eccentric pin (B) to make the adjustment. Tighten the setscrew (A).

Setscrew (A) Eccentric pin (B)

0.3-0.5mm

6

MECHANICAL ADJUSTMENT PRESSER BAR HEIGHT AND DIRECTION To check: When the pattern selector dial is set at " ", the needle should be in line with the slit of zigzag foot. The distance between the surface of needle plate and the bottom of zigzag foot should be 6.0 mm. Adjustment procedure: 1. Before proceeding this adjustment, check the zero position of zigzag stitch (page 4) and the needle drop position in needle plate hole (page 6). 2. Attach the zigzag foot. 3. Set the pattern selector dial at " ". 4. Remove the face plate. 5. Raise the foot, and loosen the setscrew (A). 6. Adjust the height and alignment of presser foot. 7. Tighten the setscrew (A) after making the adjustment.

Setscrew (A)

Needle plate

6.0mm

7 Manualsoncd.com

MECHANICAL ADJUSTMENT CLEARANCE BETWEEN NEEDLE AND HOOK To check: The clearance between the needle and hook should be 0 to 0.15 mm. Adjustment procedure: 1. 2. 3. 4. 5. 6. 7. 8. 9.

Set the pattern selector dial at " ". Turn the machine to the back. Remove the bed cover (see page 3) with bed lid, and gear box rear cover (see page 11). Take out the bobbin case and hook race ring. Loosen the setscrew (A), and move lower shaft about 0.5 mm to the right. Then tighten the setscrew (A) temporarily. Loosen the two setscrews (B). Adjust the clearance between needle and hook by moving hook race. Be careful not to turn the hook race when adjusting. Tighten the two setscrews (B). Loosen the setscrew (A), and move lower shaft to the left in order to adjust the backlash of lower shaft gear.

10. Tighten the setscrew (A) firmly. 11. Check the feed lifting cam position (page 12) and the hook timing (page 9).

0 to 0.15 mm

Shuttle race setscrew (B) (2 pcs.)

Lower shaft bushing (front)

Setscrew (A)

8

MECHANICAL ADJUSTMENT NEEDLE BAR HEIGHT To check: When the tip of shuttle hook meets the left side of the needle in ascending travel of the needle from its left and lowest position, the distance between the top of the needle eye and the tip of the shuttle hook should be in the range of 2.9-3.5mm. Adjustment procedure: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.

Remove the face cover (see page 1). Set the pattern selector dial at " ". Open the bed cover plate. Remove the shuttle race ring. Turn the handwheel toward you until the tip of the shuttle hook meets the left side of the needle. Loosen the needle bar connecting stud setscrew (A). Adjust the height of the needle bar by moving it up or down without turning it. Tighten the setscrew (A). Attach the shuttle race ring. Attach the face cover.

Tip of shuttle hook meets left side of needle 2.9-3.5mm

Setscrew (A)

Needle bar

9 Manualsoncd.com

MECHANICAL ADJUSTMENT NEEDLE TIMING TO SHUTTLE To check: The height of the needle point from its lowest point should be in the range of 1.4–2.0 mm when the tip of the shuttle hook meets the left side of the needle at the left needle position in ascending travel. Adjustment procedure: 1. 2. 3. 4. 5.

Set the pattern selector dial at " ". Remove the base (see page 5). Open the bed cover plate. Remove the shuttle race ring. Turn the handwheel toward you until the tip of the shuttle hook meets the left side of the needle. 6. Loosen the lower shaft crank arm setscrews (A). 7. While holding the shuttle hook so it doesn't turn, turn the handwheel toward you until the needle comes to its lowest position. Then, further turn the handwheel to raise the needle about 1.7 mm from its lowest position. 8. 9. 10. 11.

Tighten the setscrews (A). Turn the handwheel toward you to check if the height is in the range of 1.4-2.0 mm. If it is not in this range, repeat the above procedure. Attach the shuttle race ring. Attach the base.

Lower shaft crank arm

Lower shaft

1.4-2.0mm

Setscrew (A) (2 pcs.)

Lowest position

10

MECHANICAL ADJUSTMENT LOWER SHAFT PLAY To check: The amount of lower shaft play should be 0.3 mm or less than 0.3 mm in the axial direction. The rotary play of hook driver should be less than 0.3 mm. Adjustment procedure: 1. Remove the bed cover and gear box rear cover (see page 2). 2. If there is lower shaft play, loosen the setscrew (A). 3. While pulling the lower shaft to the right, push the feed lifting cam to the left. Tighten the setscrew (A). 4. Loosen the setscrew (B), then turn the lower shaft front bushing to adjust the backlash. 5. Tighten the setscrew (B). 6. Check the hook timing (page 9).

Gear box rear cover

Lower shaft front bushing

Bed cover

Feed lifting cam

Bed lid

Setscrew (A) Setscrew (B)

11 Manualsoncd.com

MECHANICAL ADJUSTMENT FEED LIFTING CAM POSITION To check: Put the zigzag foot between the round part of needle clamp and the bottom end of machine arm by lowering the needle bar from its highest position. Then insert the hexagon wrench into the setscrew (A). In this condition, the wrench should touch against the edge of feed rock shaft. Adjustment procedure: 1. Before proceeding this adjustment, check the hook timing (page 9) and the clearance between needle and hook (page 8). 2. Remove the bed cover (see page 2). 3. Put the zigzag foot between the round part of needle clamp and the bottom end of machine arm by lowering the needle bar. 4. Loosen the setscrew (A) with the hexagon wrench, and turn the feed lifting cam until the hexagon wrench touches against the feed rock shaft. Then tighten the setscrew (A). 5. Check the feed dog height (page 13), stretch stitch feed balance (page 14) and buttonhole feed balance (page 16).

Zigzag foot

15.0mm

Bottom end of machine arm

Round portion of needle clamp

Feed lifting cam Lower shaft

Feed rock shaft Setscrew (A)

12

MECHANICAL ADJUSTMENT FEED DOG HEIGHT To check: The distance between the highest position of feed dog and the surface of needle plate should be 0.75 to 0.90 mm when the presser foot is lowered and the stitch length dial is se at "4". Adjustment procedure: 1. 2. 3. 4. 5. 6. 7. 8. 9.

Before proceeding this adjustment, check the feed lifting cam position (page 12). Set the stitch length dial at "4". Lower the presser foot. Turn the balance wheel toward you until the feed dog comes at the highest position of travel. Open the bed lid (see page 11). Loosen the setscrew (A). Turn the eccentric pin (B), and adjust the feed dog height. Tighten the setscrew (A). Check the stretch stitch feed balance (page 14).

Feed dog

Setscrew (A)

Eccentric pin (B)

0.75 to 0.90mm Needle plate

13 Manualsoncd.com

MECHANICAL ADJUSTMENT STRETCH STITCH FEED BALANCE To check: When the machine is set for the triple strength stitch " perforation during forward and backward feeding.

", the needle should enter the same

Adjustment procedure: 1. 2. 3. 4. 5.

Set the patter selector dial at " ". Set the stitch length dial at "S.S.". Remove the top cover (see page 1). Attach the zigzag foot. Place a sheet of paper on the feed dog, and lower the zigzag foot, then turn the balance wheel toward you to check the needle perforation. 6. Turn the setscrew (A) to adjust the stretch stitch feed balance: C) If the forward feeding is longer than backward feeding, turn the setscrew (A) clockwise. D) If the forward feeding is shorter than the backward feeding, turn the setscrew (A) counter clockwise.

Setscrew (A)

S.S. rod

C

D

14

MECHANICAL ADJUSTMENT BAR-TACK FEED OF BUTTONHOLE To check: The acceptable bar-tack feeding of buttonhole should be 1 mm or less in 20 stitches when the stitch length dial is set at "4". Adjustment procedure: 1. 2. 3. 4. 5. 6.

Set the pattern selector dial at " ". Set the stitch length dial at "4". Remove the top cover (see page 1). Attach the buttonhole foot. Place a sheet of paper on the feed dog, and lower the foot. Turn the balance wheel toward you and check the feeding. 1) If the paper moves backward (in the direction of "C"), loosen the upper nut (A), then turn the lower nut (B) clockwise. 2) If the paper moves forward (in the direction of "D"), loosen the upper nut (A), then turn the lower nut (B) counter-clockwise. 7. Tighten the upper nut (A). Be careful not to turn the lower nut (B).

Nut (A) Nut (B)

Paper

C

Buttonhole foot

D

15 Manualsoncd.com

MECHANICAL ADJUSTMENT BUTTONHOLE FEED BALANCE To check: When sewing buttonhole, the stitches on each side of buttonhole should be the same stitch density. The variance of 9 to 11 stitches in the right side row against 10 stitches in the left side row is considered acceptable feed balance for buttonhole sewing. Adjustment procedure: 1. Set the stitch length dial at about "0.5" (in the range of marking " "). 2. Attach the buttonhole foot. 3. Sew a buttonhole by setting pattern selector dial in the order of " ", and check the stitch density on each side row of buttonhole. 4. Remove the top cover (see page 1). 5. Turn the setscrew (A) to make adjustment: 1) If the left side row is coaser than right side row, turn the setscrew (A) clockwise (in the direction of "B"). 2) If the right side row is coaser than the left side row, turn the setscrew (A) counterclockwise (in the direction of "C").

B

C

Setscrew (A)

Right side row is coarser

Left side row is coarser

than left side row.

than right side row.

16

MECHANICAL ADJUSTMENT

MOTOR BELT TENSION To check:

1. Improper belt tension may cause noise, overload of motor, slow running or motor belt jumping. 2. The belt deflection should be 7mm - 9mm when pressing the middle of the motor belt with approximately 300 grams of pressure.

Adjustment procedure: 1. 2. 3. 4. 5.

Remove the belt cover (see page 3). Loosen the setscrews (A) and (B). Move the motor up or down to adjust the deflection about 7mm - 9mm. Tighten the setscrews (A) and (B). Attach the belt cover.

300g Load Deflection 7-9mm

Setscrew (A)

Setscrew (B)

17 Manualsoncd.com

PARTS LIST MODEL: HD-1000BE

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

721609403 731097A01 730501011 000160102 731004001 000109000 735016307 000071013 000101828 000061205 731005301 730015002 730016003 000107204 000104108 000101404 730604107 730502104 730018108 000002806 730019006 721602071 721008705 840602006 366076000 100411104 730601805 730004503 730005504 730006000 000021409 830312016 000101703 731502303 731050301 731051302

DESCRIPTION Top cover (unit) Top cover Thread guide plate (unit) Adjustable lock nut 4 Top cover thread guide Setscrew 3x6 Bobbin winder stopper Washer 4 Setscrew 4x16 Nut 4-3-7 Handle Carrying handle shaft Carrying handle set plate Setscrew 3x12 (B) Setscrew 4x20 Setscrew 4x6 Bobbin winder (unit) Bobbin winder arm (unit) Bobbin winder set plate Snap ring E-6 Bobbin winder spring Face plate (unit) Face plate Thread cutter (unit) Face plate sticker Lamp sticker Bed cover (unit) Bed cover Bed lid Spring Spring pin 2.5x10 (K) Caution sticker Setscrew 4x12 Extension table (unit) Extension table Extension table lid

19 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

2

4

35 34

2 1 17 16 3 5

12

2

14 7

11

6

13

9

8

10

2

8

15

2

29 31

21

18

20 19 25

23

30

24

22

28 41

26

27 33

39

37 40

38

32 36

41

20

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

647513004 000101404 000009803 693047005 731636101 731099106 730029009 000013903 730030003 730031004 000103808 721502519 721009005 303017008 730026006 802021007 802022008 822069009 000111500 102222009 822071004 822072005 000103509 000072302 611520003 611510000 611511001 647112009 680036001 000066303 000070506 731009006 000100300 731006405 000115700 721603407 721010401 721011000 000120203 000070104 000103004

DESCRIPTION Lamp socket (unit) Setscrew 4x6 Lamp 120V 15W Cord holder Front bracket (unit) Front bracket Thread tension release lever Snap ring CS-5 Thread tension release plate (1) Thread tension release plate (2) Setscrew 3x5 Thread tension (unit) Thread tension fixing plate Presser bar Presser bar spring Presser bar bushing Snap retainer Presser bar supporter Hexagonal socket screw 4x8 Spring Presser foot lifter Presser foot lifter pin Setscrew 4x10 Washer 4 Presser foot (unit) Presser foot holder Zigzag foot Thumbscrew Stopper Hexagonal bolt 4x6 Washer 4 Arm thread guide Setscrew 3.5x5 Spool stand Setscrew TP 4x10 Front cover (unit) Front cover Face plate stopper plate Setscrew 3x8 (B) Washer 3 Setscrew 3.5x6

21 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

24

4 1

23

6

26

5

24

27

2 3

14 17

18

28

21 20 7

7

12

19

15

13 17

9

22

10 8 16 11

25

29

33 32

30

31

22

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33

303604101 303020107 730022002 673022002 000070609 000002507 000111902 303605009 303016007 000003508 755643002 000125105 840035002 303064000 840037004 840034001 000078319 734625003 734101008 734102009 000097602 730503116 680504005 000111304 102408089 625506109 647040108 730509008 730023003 748021006 678084007 730024107 000101404

DESCRIPTION Needle bar supporter (unit) Needle bar supporter Needle bar supporter pin Spring washer Plain washer 6 Snap ring E-4 Hexagonal socket screw 3x4 Needle threader shaft (unit) Needle threader shaft Spring pin 2x8 Needle threader guard plate (unit) Guide pin E-2x16-CH Needle threader spring Needle threader guide plate Needle threader lever supporter Needle threader lever Setscrew 3x6 Threader positioning setting plate (unit) Threader positioning setting plate Threader positioning setting base Setscrew 2x4 Needle bar (unit) Needle bar connecting stud (unit) Hexagonal socket screw 5x5 Needle Thread take-up lever (unit) Thread take-up lever pin (unit) Needle bar crank pin (unit) Zigzag rod Zigzag rod washer Eccentric pin Needle bar supporter spring Setscrew 4x6

23 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

22 1 8

21

6 5

7

4 18 3 2

19

8

20

11 13

9

17

10

16 15

24

12

14

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

731604007 102073003 102063000 000111304 553245008 000110303 735143005 731312005 730036504 730037000 102076006 647036400 647037009 102078101 671106005 640008000 000105202 738634007 673103008 000002806 671021005 000111108

DESCRIPTION Upper shaft (unit) Screw Screw Hexagonal socket screw 5x5 Hexagonal socket screw Hexagonal socket screw 4x6 (WP) Felt Felt Handwheel Handwheel bushing Motion washer Motion screw Washer Setscrew Setscrew Balance weight Setscrew 3x12 Crank rod (unit) Feed rock shaft connecting pin Snap ring E-6 Upper shaft rear bushing Hexagonal socket screw 4x6

25 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

3

4

1

4

4

19

2

20 4

21 4

14 16 18 13 17 5 6 7

11

15

8 9

12

10

26

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

731662025 731663129 730092003 000101404 731645103 648010009 000160102 803134007 000000309 802097004 735077007 730041007 731658084 731607000 721606503 000014306 731029002 000081005 721203A01 721017A01 000104005

DESCRIPTION Zigzag mechanism (unit) Pattern selector dial (unit) Spring Setscrew 4x6 Feed regulator (unit) Setscrew Adjustable lock nut 4 Feed regulating body spring Snap ring E-40 (I) Hexagonal socket screw Feed regulating body spring Spring guide Feed dial (unit) Feed regulating cam (unit) Reverse button (unit) Snap ring CS-3 Feed dial spring Setscrew 4x8 Ornamental plate Feed front cover Setscrew 3.5x8

27 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

1 4

16

19

18

7 17

2

10

13 20

9 16

12 8

3

17 11

21

14 15

5 6 22 28 26 27

24 23

31 30 29

32

28

25 8

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32

730611004 730057006 647066007 647134007 648019008 102021202 000002507 000111108 730184003 730183002 672042005 647612015 647064005 102151006 102205006 738055008 000111304 647607006 102141003 673103008 000002806 730612005 738028002 735090109 730059008 730061003 730062004 365032001 730063016 000101703 730064006 000101404

DESCRIPTION Feed rock shaft (unit) Feed rock shaft Feed dog base Feed dog base shaft Feed dog base sliding plate Setscrew Snap ring E-4 Hexagonal socket screw 4x6 Feed dog Setscrew Feed dog base spring Feed rock shaft crank (unit) Feed rock shaft crank Setscrew Setscrew Straight pin Hexagonal socket screw 5x5 Fork rod (unit) Feed regulator slide block Feed rock shaft connecting pin Snap ring E-6 Feed lifting arm (unit) Feed lifting arm Feed lifting arm shaft Drop feed selecting plate Drop feed selecting spring Sliding plate Flat screw Feed lifting crank roller shaft Setscrew 4x12 Feed lifting arm shaft holder Setscrew 4x6

29 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

14

15

16

9 11

12

13 4

10

8

18

11 4

4 11

4 17

7 19

1

20

21

6 4 2

22

3 5

4

30

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

640603104 640503000 532096007 000111304 647515006 102261000 640018003 626045603 647142008 730038001 000110107 738024008 647043008 640038009 822070003 738023007 730027007 681009101 730107002 000101404 730109004 000101208

DESCRIPTION Hook race (unit) Hook race Hook Hexagonal socket screw 5x5 Bobbin case (unit) Bobbin Hook driver shaft bushing Cap Lower shaft Lower shaft gear Hexagonal socket screw 5x5 (WP) Lower shaft front bushing Feed lifting cam Lower shaft rear bushing Felt Lower shaft crank Needle plate Flat screw Gear box upper cover Setscrew 4x6 Gear box rear cover Setscrew 5x6

31 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST

1

2

11

16 7 6 9

3 12

8

3 5 4

10 17

18

13 19

15

22

14

20

4 23 21

32

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23

730010A01 647009002 000081005 000107204 731668009 730008002 000061319 647009002 647010006 000066808 731161306 000104119 731515000 731380107 000121400 624093013 013596307 000115504 000053008 731379000 731381005 639511018 000101404

DESCRIPTION Base Bed rubber cushion Setscrew 4x8 Setscrew 3x12 (B) Arm leg (unit) Arm leg Nut 5-1-8 Bed rubber cushion Adjusting screw Setscrew 6x14 Belt cover Setscrew 4x20 Machine socket (unit) Machine socket set plate Setscrew 3x14 (B) Timing belt Motor (unit) Setscrew TP 5x10 Cord binder Switch set plate Indicator plate Switching power supply Setscrew 4x6

33 Manualsoncd.com

MODEL: HD-1000 BE

PARTS LIST 1

3

2

4

5

6

7

8

9

10

11

12

14

13

16

15

17

18

34

MODEL: HD-1000 BE

PARTS LIST

KEY PARTS NO. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18

731870800 647802003 647803004 102403109 741814003 102261000 647808009 540401026 737801015 743815000 611604002 674401002 214509003 940250000 731424001 C-1028 731402195 465722204

DESCRIPTION Accessory set Large screw driver Small screw dirver Felt Oil Bobbin Seam ripper/Buttonhole opener Needle case (unit) Buttonhole foot Hemmer foot Zipper foot Hem guide Even feed foot Ultra glide foot Leather needle Foot control Instruction book (English/Spanish/French) Cover

35 Manualsoncd.com