231 29 27MB
English Pages 52 Year 1970
AND SERVICE INFORMATION ON KEY-IN-THE-KNOB LOCKS
~ PUBLISHED
me
Ce ,
BY
ae
THE
LOCKSMITH
real eed
pote
=
Sees
VOLUME EXPLODED and
SERVICE
2
LOCK
VIEWS
INFORMATION
on
KEY-IN-THE-KNOB LOCKS including PADLOCKS and PANIC EXIT BOLTS
This supplemental edition of Exploded Lock Views is being issued to provide under one cover all of the new locksets introduced since the time of release of the original EXPLODED LOCK VIEWS manual. When used together, these two manuals provide
service
information
and technical
data on
the majority of the popular locksets of today. Since manufacturers are constantly revising and improving their locks, the reader may find occasional variations between the illustrations and the
actual
locks
he may be working
upon.
These
differences, however, are minor and will not detract from the value of this edition because the basic principles are unchanged.
Published By
Nickerson & Collins Publishing Co:: Locksmith Ledger Div. 2720 Des Plaines Ave. Des Plaines, Ill. 60018 Copyright, 1970
LOCKSMITH LEDGER
Little Falls, N. J.
=
\\ \
EXPLODED VIEW DEXTER No. 3231 Manufactured Dexter Industries,
by Dexter Lock Division, Inc., Grand Rapids, Michigan
A.
Cylinder
J.
Retainer Clip
B.
Outside Knob
K.
Latchbolt
C.
Outside Rose
L.
Retainer Clip
D.
Knob
M.
Inside
N.
Spindle Drive Washer
O.
Spindle
P.
Knob
Shank Stop Washer
Q.
Push
Button
R.
Inside Rose
S.
Inside
EK. F.
G.
Shank
Stop
.
.
Outside Mounting Knob
Retainer
Retainer
Washer Plate
Mounting
Plate
Washer
Clip
H.
Knob
Return
I.
Knob
Travel
Spring Stop Washer’
Knob
Assembly
SERVICE
NOTES
To
remove the lockset from the door, insert a screwdriver or similar tool into the knob release hole of the inside knob, de-
TURN WY
press the knob retainer and pull knob off. Then insert a screwdriver between the notch in the inside rose and the tab on the inside mounting plate; then, pry off inside rose. The inside mounting plate then can be released from the tie screws, enabling the entire outside knob assembly to be removed from the door. Note that one of the tie screws goes through the latch, while the other goes through an indentation in the end of the latch.
180°
OF
Sa
UW
5
4
MUST CLEAR TAB
To remove the cylinder assembly from.the outside knob, insert, the key and rotate it 180°, (onehalf turn). This will bring a groove in the cylinder cam in line with
a retaining
tab
in the
knob spindle, enabling the cylinder to be pulled out. To install the inside rose, position the rose to the mounting plate tab; then, snap rose in place. When installing the in-
side push
knob
on
button
the
sleeve
assembly,
of the be
sure
the guide in the knob shank engages
in the
slot of the
sleeve.
The knob then can be pushed in until it snaps in place.
Page 3
EXPLODED VIEW E-Z-SET 500 Manufactured by National Hardware Corp.
QMO
AW
>
Ozone Inside Knob Assembly Latch Bolt
Turn
and
Button
Stem
4
H. I. J.
Knob Retaining Lug Pin Knob Retaining Lug Spring
K.
Inside Spindle
Assembly Retaining Nut
L. M.
Cylinder Spring
Outside
N.
Cylinder
O.
Outside
Rose
Locking Washer
Cylinder
Stem Knob
Housing
L
Page
Rose
Park, N. Y.
M
N
O
SERVICE
NOTES
To
remove the cylinder housing and cylinder from the outside knob (after the outside rose has
been
removed),
pull out the
knob retaining lug pin from the evlinder housing with a pair of needle nosed pliers. The knob retaining lug then can be removed by pressing down at one end to raise the opposite end, and using tweezers or pliers to
grasp the upraised end to lift it out of the slot. The retaining nut “D” is removed with a_ special socket wrench available from the manufacturer. The numbers stamped on the bow of the original key indicate the depths of the cuts, reading from bow to tip.
Page
5
EXPLODED LOCK VIEW LOCKWOOD RS-130 Manufactured by Lockwood Mfg. Fitchburg, Massachusetts
Co.
A.
Outside Knob
G.
Housing Cover
B.
Cylinder
H.
Latch Bolt Assembly
C.
Outside
I.
Inside
D.
Outside Spindle Assembly
E.
Springs
J.
Inside Rose
F.
Push Plate
K.
Inside Knob
// \ “li,
Page 6
Rose
Spindle
and
Button Assembly
Push
SERVICE NOTES
ls PRESS
To
remove
7
TURN
CATCH
inside
knob,
turn
it as far as it will go and depress the catch exposed in the hole of the inside rose.
To replace the outside knob on the outside spindle, insert the cylinder in the knob, lining up the retaining groove in the knob with the retainer exposed through the hole in the outside
rose,
which
is mounted
on
the
spindle. Slide the knob on the spindle; then insert the key and turn the cylinder until its twin tails fall into place in the spindle, which will enable the knob retaining groove to slide over the retainer.
The action in opening the lock with a key is shown above. As the key is turned, the cylinder
activates
a pusher
arm,
which
in turn, activates the push plate, retracting the bolt.
When
the
inside
button
is
pushed in, the push button stem moves sideward, moving a lug into a locking position in the
push plate.
Page
7
EXPLODED VIEW Lockwood “’S” Series Manufactured
Outside
by Lockwood Hardware Manufacturing Fitchburg, Massachusetts
Knob
Cylinder Outside
Knob
Collar
Company
Outside Rose Retractor Housing
Outside Knob
Spindle
Key Release Spindle Spring Push Button Stem Retractor Latchbolt
L. M.
Inside Knob Spindle Push Button Spindle Retaining Screw
CARBO HOZ
G. H. I. J. K.
Service This
lockset
is adjustable
for
doors having thicknesses of 13” and 134”. For doors, 138” thick,
Push Button Partial Retractor Housing Housing Cover Retaining Screws Inside Rose Adjustable Sleeve Inside Knob Collar Inside Knob
Notes partial
retractor
housing,
using
the special spanner wrench sup-
the
plied with the lockset to tighten it securely.
threaded portion of the retract-
To adjust for doors 134,” thick,
screw
the
outside
rose
on
screw
outside
knob
on_
the
or housing base. Final tightening for the door thickness adjustment is made with the inside
threaded portion of the retractor
rose. Before
slipping on the in-
from the retractor housing base.
side rose, make a mental note of the position of the retainer hole
Final tightening for door thickness adjustment is made with
in the sleeve attached to the inside knob. Then, slip rose into position and screw it on the
the inside rose in the same man-
housing
spindle
ner as for doors thick. (described
until
it is
that are above).
3”
13”
Page 9
EXPLODED LOCK VIEW Reddi-Mount 500 Nassau X95-3 Includes latest construction changes
Mfg. by J. Chesler & Sons, Inc., Brooklyn, N. Y. A.
Cylinder
B,
Connecting
bers
are
key
depths) Springs
Spring
Chamber
(Holds Outside
“D” in Rose of Knob Assembly
F
Speed
G.
Housing
Body
i.
Spring
Guides
i;
Latch
J.
Latchbolt
10
Ly,
Free
M.
Pusher
Cover
Coupling
Retainer Spring Cover
lever
Plate
holds
hub
and acts as a neutral cam)
-
Nut
Retractor
Spinning
Hub
OYOZ
Return
Mom
New
Cross Bar Pins Latchbolt Case Dogging
Screw
Dogging
Key
Support Case Cover Support Case Cross
Bar
Cross
Bar
Spacing
Ring
Page 41
PANIC
LOCK
ASSEMBLY
CHARTS
SARGENT & GREENLEAF MODEL NO. KD5300C Manufactured by Sargent & Greenleaf, Inc. Rochester 21, N. Y.
Page 42
A—Dogging
Key
B—Cover C—Operating D—Cylinder
Handle Cam
Spring
(for tailpiece
outside
cylinder)
E—Dogging
Keyway
of
F—Dog G—Operating
Handle
Pivot
Pin
H—Case I—Operating
Handle
J—Bolt
Pin
K—Bolt
Pivot
Assembly
Spring
L—Bolt
}
Page 43
PANIC
LOCK
ASSEMBLY
CHARTS
VON DUPRIN No. 1056A Mfg. by Von Duprin Division, Vonnegut Hardware Co. Indianapolis, Ind.
Page 44
I
A—Case
Cover
B—Latch
Lever
C—Cylinder
Arm
Hub
D-—Lever
Arm
Pusher
E—Lever
Arm
Pusher
F-—Latch
Pin
Spring
G—Latch Bolt H-—Latch
Lever
I—Thumb
Piece Lever
J—-Screw K—Locking Lever Spring L—Thumb
piece
Positioning Locking
Lever
M-—Case N—-Thumb
Latch
Handle
Assembly O-—Dogging P—Case
Key
Lever
Q—Cross R—Support
Bar Case
Page 45
PANIC
BOLT
ASSEMBLY
CHARTS
Sargent and Greenleaf Model
No. KD5311
Manufactured by Sargent & Greenleaf, Inc., Rochester 21, N. Y.
TED 62 Pd BOOe
M
Page 46
Case Case
Screws
J. Cross Bar Spring K. Dogging Screw KK . Dogging Key
Cylinder Hub Latch
Bolt
Latch Bolt Spring Roller Cam Pin Roller Cam Case Cross Bar Cross Bar
Pin
L.
Case
O. P,
Support Case Support Case Cross Bar Pin Travel Stop Pin Cross Bar Spring Cross Bar
M. N.
Q
Cover
KEY IN THE KNOB IDENTIFICATION BY TRADE NAME Salesmen
and
hardware
tomed to referring
men
are
to certain key
by name instead of numbers. will help you quickly identify the be talking about. Trade
Name
becoming
accus-
in the knob locks The following list product
they
may
Manufacturer
ALIGNALOCK CHALLENGER
Sargent & Co. Challenger Lock Co.
(formerly Hollymade) DEFENDER DEXLOCK
Corbin Dexter
E-Z-SET GUARDIAN HAMPTON HOMEGUARD HOME DUTY INTEGRALOCK OLYMPIC-ROYAL PACEMAKER PRESIDENT REDDI-MOUNT ROYAL S.A. F.E SENTRY STILEMAKER STILEMANOR SHURLOC
Lock Division
Dexter Industries, Inc. National Hardware Corp. Corbin Harloc Russwin Yale
Sargent & Co. Vimcar (out of business) Harloc
Vimcar (out of business) J. Chesler & Sons (out of bus) Vimear (out of business) Distributed as TACO Lockset by Trans-Atlantic Co. Sargent & Co. Russwin Russwin Metallon
Products
(formerly Technical Glass) WESLOCK Note:
The
Western above
names
are
styles
Lock Mfg. of locks
Co. and
are not to be confused with designs which are also named by the various manufacturers.
Page 47
LOCKSETS:
Arrow 150______________ ~~~ Le DExter 32351 a ee E-Z-Set
500___________________
24 2 _
4
Lockwood RS-130______-____ ______
6
Lockwood "S''Series__________
8
Reddi-Mount 500______________________ Russwin U240________ > Le
10 12
Sargent Sentry Lock__________________ 14 Schlage D85PD_________§ _§ _____
16
Shurlok
LL
220
i
22
735. ~_____________
Sc Pls Bhs Be
“(URC a
ce
Weiser 500 (Improved)________________. Weslock 8380__________~______ ee __ Weslock 930_.______________ ee Yale 5400_________________ Le
26 28 30 32
PADLOCKS: Corbin Sesamee
(Improved)______________ __ 35 Sargent & Greenleaf 8088___ ______________- __ 36
Sul (Foreign)___ PANIC
_._-_ ---_-___-____
a
EXIT DEVICES:
Corbin No. 1DB 2885_____________________ 38 Sargent No. 5800_____.________et 40 Sargent & Greenleaf No. KD5300C_________ __ a 42 Sargent & Greenleaf No.
KD5311____--_-_-____-~_ ee
Were outpace
46
44
Publisher's
righted. in any
Note:
All
material
in this
book
Nothing appearing herein maybe
way
without
permission
of the
is
copy-
reproduced
publisher.