Tribological design of machine elements 0444874356, 9780444874351, 9780080875781

Table of contents :
Content:
Edited by
Page iii

Copyright page
Page iv

Introduction
Pages ix-xi
Duncan Dowson, Chris Taylor

The Tribological Design of Machine Elements Original Research Article
Pages 3-12
H.S. Cheng

Tribological design - The aerospace industry Original Research Article
Pages 15-21
J.A. Dominy

Tribological design-The railways Original Research Article
Pages 23-32
C. Pritchard, T.G. Pearce

Tribological design-The automotive industry Original Research Article
Pages 33-39
P.A. Willermet

Tribological design - The process industries Original Research Article
Pages 41-44
J.D. Summers-Smith

Design of Controllable Mechanical Seals Original Research Article
Pages 47-55
R.F. Salant, O. Giles, W.E. Key

Micro-elastohydrodynamic lubricant film formation in rotary lip seal contacts Original Research Article
Pages 57-68
A. Gabelli

Lubrication of reciprocating seals: Experiments on the influence of surface roughness on friction and leakage Original Research Article
Pages 69-77
A.F.C. Kanters, M. Visscher

Radial lip seals, thermal aspects Original Research Article
Pages 79-88
M.J.L. Stakenborg, R.A.J. van Ostayen

Lubrication and fatigue analysis of a cam and roller follower Original Research Article
Pages 91-100
B.A. Gecim

Predictions of cam wear profiles Original Research Article
Pages 101-109
R.H. Fries, C.A. Rogers

Cam and follower design Original Research Article
Pages 111-130
A.D. Ball, D. Dowson, C.M. Taylor

Power transmission by flat, V and timing belts Original Research Article
Pages 133-142
T.H.C. Childs, I.K. Parker

Power rating of flat belt drives - A wear approach Original Research Article
Pages 143-147
B.G. Gerbert

The relationship between uneven tooth contact loading and surface durability in flexible gear designs Original Research Article
Pages 151-160
J.F. Harrop, A. Tam

Temperature and pressure measurements in gear contacts with thin-film-transducers Original Research Article
Pages 161-165
H. Peeken, P. Ayanoglu

A static and dynamic analysis of misaligned gears with partial contact areas Original Research Article
Pages 167-172
Ph. Sainsot, Ph. Velex, D. Berthe

The Palmgren-Miner rule derived Original Research Article
Pages 175-179
J.J. Kauzlarich

Prediction of rolling bearing life under practical operating conditions Original Research Article
Pages 181-187
E. loannides, B. Jacobson, J.H. Tripp

Surface damage on rolling elements and its subsequent effects on performance and life Original Research Article
Pages 189-197
J.C. Hamer, A.A. Lubrecht, E. loannides, R.S. Sayles

Debris denting-The associated residual stresses and their effect on the fatigue life of rolling bearing: An FEM analysis Original Research Article
Pages 199-207
C.N. Ko, E. loannides

Axially profiled circular bearings and their potential application in high speed lubrication Original Research Article
Pages 211-218
S. Basri, D.T. Gethin

Analysis of partial arc journal bearings Original Research Article
Pages 219-228
E.W. Cowking

Elapsed time for the decay of thermal transients in fluid film bearing assemblies Original Research Article
Pages 229-235
C.M.M. Ettles, H. Heshmat, K.R. Brockwell

Design procedures based on numerical methods for hydrodynamic lubrication Original Research Article
Pages 237-242
J.O. Medwell

The effect of residual stress and temperature on the fretting of bearing steel Original Research Article
Pages 245-252
M. Kuno, R.B. Waterhouse

The wear of hot working tools. Application to forging and rolling of steel Original Research Article
Pages 253-258
E. Felder

The influence of debris inclusion on the performance of polymeric seals in ball valves Original Research Article
Pages 259-265
B.J. Briscoe, P.J. Tweedale

Tribological characteristics of needle bearings Original Research Article
Pages 269-276
S. Blair, W.O. Winer

Power loss prediction in ball bearings Original Research Article
Pages 277-286
R.J. Chittenden, D. Dowson, C.M. Taylor

The effect of roller end-flange contact shape upon frictional losses and axial load of the radial cylindrical roller bearing Original Research Article
Pages 287-295
H. Krzemiński-Freda, B. Warda

The study of roller end and guiding shoulder construction of roller bearings Original Research Article
Pages 297-301
M. Li, S. Wen

Dynamically loaded journal bearings: a modal approach to EHL design analysis Original Research Article
Pages 305-315
A. Kumar, J.F. Booker, P.K. Goenka

Shape defects and misalignment effects in connecting-rod bearings Original Research Article
Pages 317-322
P. Maspeyrot, J. Frene

Transient dynamics of engine bearing systems Original Research Article
Pages 323-332
S. Boedo, J.F. Booker

Thermal considerations in engine bearings Original Research Article
Pages 333-342
G.A. Clayton, C.M. Taylor

Design requirements of ceramic sliding contacts Original Research Article
Pages 345-348
R.J. Gozdawa, T.A. Stolarski

Unlubricated wear and friction behaviour of alumina and silicon carbide ceramics Original Research Article
Pages 349-354
G. Kapelski, F. Platon, P. Boch

The effects of surrounding atmosphere on the friction and wear of ceramics Original Research Article
Pages 355-364
S. Sasaki

Wear performance of materials for ball screw and spline applications in Candu reactor fuelling machines Original Research Article
Pages 365-370
P.E. Dale, R. Tristani

Tribological design-The power generation industry Original Research Article
Pages 373-382
P.G. Morton

Tribological design and assessment-The nuclear industry Original Research Article
Pages 383-388
T.C. Chivers

Tribological design-The spacecraft industry Original Research Article
Pages 389-396
R.A. Rowntree, E.W. Roberts, M.J. Todd

Tribological design - The electronics industry Original Research Article
Pages 397-408
E.A. Muijderman, A.G. Tangena, F. Bremer, P.L. Holster, A.v. Montfoortand

Optimum design and automatic drawing of recessed hydrostatic bearings Original Research Article
Pages 411-418
S. Xu, B. Chen

Computer aided design of externally pressurized bearings Original Research Article
Pages 419-424
G.J.J. van Heijningen, C.M. Kalker-Kalkman

A theoretical investigation of hybrid journal bearings applied to high speed heavily loaded conditions requiring jacking capabilities Original Research Article
Pages 425-433
D. Ives, W. Weston, P.G. Morton, W.B. Rowe

Behaviour of a high-speed hydrostatic thrust bearing with recess inserts and grooved lands Original Research Article
Pages 435-444
D. Ashman, E.W. Parker, A. Cowley

An experimental comparison between the performance of a ‘total cross flow’ and an equivalent conventional design hydrostatic journal bearing Original Research Article
Pages 445-454
M. Abdolmaleki, A. Skorin, F.P. Wardle, R.A.E. Wood

Review Paper: Tribological design - Information storage and retrieval Original Research Article
Pages 457-469
B. Bhushan

Active magnetic bearing design methodology-A conventional rotordynamics approach Original Research Article
Pages 471-478
H.M. Chen

The incorporation of artificial intelligence in the design of herringbone journal bearings Original Research Article
Pages 481-488
K. Ishii, B.J. Hamrock, J. Klinger

Bearing selection using a knowledge based system Original Research Article
Pages 489-493
R.T. Griffin, M.J. Winfield, S.S. Douglas

Tribology aids for designers Original Research Article
Pages 495-499
C.J. Thijsse

Written Discussions and Contributions
Pages 503-512

List of Authors
Pages 513-516

List of Delegates
Pages 517-522